Photon Number Resolution (PNR)
Introduction to photon number resolution (PNR)
Photon number resolution (PNR) is an enabling technique used to assign the number of photons involved in a detection event precisely. This technique leverages photon-number-resolving single-photon detectors as well as sophisticated signal analysis, and it is necessary for quantum cryptography 1 and quantum communication 2.
There are several types of single-photon detectors, such as photomultiplier tubes (PMTs), single-photon avalanche diodes (SPADs), transition edge sensors (TESs), and superconducting nanowire single-photon detectors (SNSPDs). In comparison with the other types, SNSPDs have better sensitivity at telecom wavelengths, low dark counts, and can reach picosecond time resolution, making SNSPDs a key tool in quantum research. Indeed, the development of SNSPD has led to outstanding results in quantum technology 34.
Despite advancements in detector development, detecting and recognizing more than one photon acquired from the same pulse is a challenging quest. Typically, multiple single-photon detectors are coupled in parallel to spatially distinguish a different number of photons collected at each event 5. The problem with this pseudo-PNR configuration is a high cost, as well as a non-zero probability that two photons are absorbed by the same pixel at the same time.
The analysis of the signal recorded from the SNSPD helps to overcome this problem.The SNSPD signal’s shape depends on the number of photons absorbed, as shown in Figure 1. The rising slope of the signal increases with a higher number of photons 67. It is feasible to ascertain the number of absorbed photons employing temporal correlation analysis between the electrical pulses from the detector and the laser source, thereby accentuating disparities in slopes of the SNSPD signal’s rising edge. Additionally, the falling edges of SNSPD signals shed light on the origins of the signals as well as the fluctuations inherently present in the experiment 68.
The possibility of simultaneously measuring different signals and their corresponding rising and falling edges are game-changing factors in PNR measurements, and this is where the power of the Swabian Instruments’ Time Tagger comes into play.
Unlike conventional time tagging devices, which can typically only detect one edge, Swabian Instruments’ Time Taggers can simultaneously acquire rising and falling edges to capture a wide variety of signal profiles. The ability to capture both edges of the signal is a crucial factor not only in PNR measurements but also in experiments in which a constant fraction discriminator approach is required due to variations of amplitudes and widths of the detector pulses (e.g., PMTs).
Timing electronics required for photon number resolution (PNR) experiment
Photon number resolution (PNR) experiments require precise and reliable information on the timing of the acquired events. Time-to-digital converters must perform fast operations and achieve sufficient time resolution for distinguishing the number of photons. In its turns, power sources and detectors must be stable and low-noise.
A typical setup for a PNR experiment is shown in Figure 2. This setup includes a photon source, light modulators, superconducting nanowire single photon detectors (SNSPDs), and a time-to-digital converter. For demonstrative purposes, a laser is used as the photon source from where the emitted photons are adapted and shined onto the SNSPDs. The photons impinging on the detector lead to the formation of a “hot spot”, and as a result, the SNSPD loses its superconductivity characteristics and generates a signal, which indicates the detection event - a click. The time-to-digital converter Time Tagger allows the precise and simultaneous determination of the clicks’ arrival time as well as the emission time of the photons emitted by the photon source. When the trigger signal from the laser is not directly available, the timing information of the incoming photons can be acquired with a dedicated photodiode, which collects part of the light from the photon source.
The critical hardware characteristics of a time-to-digital converter required for PNR experiments:
- Timing jitter. The lower the timing jitter of the timing electronics is, the better the resolution and precision of the measurement will be. One has to take into account the jitter from SNSPDs, which is of the order of 4 ps (RMS jitter), and try to keep the timing jitter from the electronics below this value.
- Dead time. Minimizing dead time is imperative to prevent data loss, especially when dealing with high photon count rates. Currently, the minimum dead time of SNSPDs is of the order of 10 ns. Swabian Instruments Time Taggers feature deadtimes below the conventional SNSPDs in the market, preventing data loss in your most advanced experiments.
- Data transfer rate. Higher data transfer rates allow the capture of more photon events in a shorter time window, thereby increasing the statistical significance of measurements. Insufficient data transfer leads to overflow and data loss unless data filtering methods exist to control data acquisition before being transferred to the PC. The successful data filtering method will utilize the total sum of the count rates for each of the channels (including laser, detector, controllers, signal triggers, etc) to determine the clicks that must be transferred.
Swabian Instruments’ Time Taggers - an advanced solution for precise photon number resolution (PNR) measurements
Results demonstrated by Swabian Instruments’ Time Tagger in precise photon number resolution (PNR)
Swabian Instruments’ Time Taggers are powerful tools used to gain precise knowledge of the photons’ arrival time. Therefore, their implementation is a key factor in precise photon number resolution (PNR) measurements. In a recent publication by G. Sauer et al. 6, a Time Tagger X was employed to read the signal from superconducting nanowire single-photon detectors (SNSPDs).
The approach of PNR experiments with SNPDSs is well established. However, conventional PNR measurements are carried out with several SNSPDs in parallel.
The cost-efficiency and precision of this pseudo-PNR method pose limitations. Here, the authors demonstrate how, with just a single SNSPD, it is possible to extract accurate PNR information from the detected signal. As shown in Figure 3, there is a clear distinguishability of photon modes with up to 5 photons. Thanks to Time Tagger X , it is now possible to measure the number of photons precisely using a single SNSPD, and with this method, the measurements can be precisely calibrated.
Application notes
Time-Correlated Single-Photon Counting with Single Quantum EOS SNSPD System
TCSPC_Swabian_Instruments.pdfPhoton Number Resolution with Room Temperature Detector
Photon_number_resolution_with_room_temperature_detector.pdfCustomer success stories
Brandon Ginkemeyer, Harvard
I really like the Swabian Instrument’s usability and reliability. A senior student in my neighboring group said that the Time Tagger is his favorite instrument.
Read moreDr. Ted S. Santana, NPL
My experience with the Swabian Time Tagger has been excellent. It is a truly plug-and-play device with intuitive and user-friendly software.
Read moreRelated News

Simplifying Photon Detection and Analysis with Time Taggers
Photon detection distinguishability is increasing interest in advancements in photonics and quantum technology. At Swabian Instruments, we are proud to lead this innovation with our Time Taggers, as detailed in our latest abstract presented at the Optica Latin America Optics and Photonics Conference, which took place in Puerto Vallarta, Mexico, in November 2024.
Read more
The First Photonic Quantum Computer in Germany: Swabian Instruments' Role in this Breakthrough
Quantum technologies are transforming our world. The study of quantum particles brings us closer to realizing technology that once seemed impossible. From revolutionizing quantum research and advancing drug development to cryptography, there are fields where quantum computers are positioned to surpass even the best classical supercomputers. This month is marked by great news—the launch of the first photonic quantum computer built in Paderborn, Germany! At Swabian Instruments, we’re proud to have enabled this breakthrough with our software-based Photon Number Resolution on single SNSPDs!
Read moreA. Gaidash, et al. „Revealing beam-splitting attack in a quantum cryptography system with a photon-number resolving detector.", JOSA B, 33:1451–5 (2016) ↩︎
F.E. Becerra, et al., „Photon number resolution enables quantum receiver for realistic coherent optical communications.", Nat Photonics, 9:48 (2015) ↩︎
K. Nicolich, et al., “Universal Model for the Turn-on Dynamics of Superconducting Nanowire Single-Photon Detectors.”, Phys. Rev. Applied, 12, 034020 (2019) ↩︎
C.R. Fitzpatrick, et al., „A superconducting nanowire single-photon detector system for single-photon source characterization.", Proceedings of SPIE, 7681, 768105 (2010) ↩︎
F. Marsili, et al., “Superconducting parallel nanowire detector with photon number resolving functionality.”, Journal of Modern Optics, 56:2-3, 334-344, DOI: 10.1080/09500340802220729(2009) ↩︎
G. Sauer, et al., “Resolving Photon Numbers Using Ultra-High-Resolution Timing of a Single Low-Jitter Superconducting Nanowire Detector.”, arXiv:2310.12472 [quant-ph] (2023) ↩︎ ↩︎ ↩︎ ↩︎ ↩︎
Mamoru Endo, et al., “Quantum detector tomography of a superconducting nanostrip photon-number-resolving detector.”, Opt. Express 29, 11728-11738 (2021) ↩︎
T. Schapeler. Et al., “How well can superconducting nanowire single-photon detectors resolve photon number?”, arXiv:2310.12471 [quant-ph] (2023) ↩︎